Evnroll Mallet Putters

Evnroll Mallet Putters

イーブンロール　パター　EVNROLL　PUTTERでボ−ルが集まります。。日本未発売です。 面白い実験 同じ太さの二本の棒を用意して（約30センチ）。2本の棒の左片方をくっつけて片方を少し離して（1センチ）平坦なテーブルの上におきます。其の上にゴルフボールを置きます。1センチの幅を少しづつ開くと、ボールは棒の間隔幅の広いほう右側へ動きます。ボールの重力が其の重さで逃げが起きる現象ですね。。 フェースの広い範囲で打っても1点にボールが集まるので、かなり有利な条件でパターをする事になります。 何が凄いのかというと。。科学的でここまで一生懸命にパターを考えている人が居るんだな〜と、感激しました。 下の図を見てください。パターロボットで各緒条件を固定しEVNROLLのフェースの在る無しでテストした結果なのです。つまり、パターフェースの違いだけで下記の図ように異なるのです。 左が、普通のパター、右がEVNROLLです。 打つ場所が異なってもボールは真っ直ぐ行く事を証明しました。スペックER10 Outback Black Experience the sweetest face in golf with the Evnroll ER10 Outback Black Putter. A lightweight 6062 aluminum body is combined with a rear CNC milled 303 Stainless steel “Outback” shaped weight to elevate stroke consistency and control. Sweet Face Technology utilizes closely spaced, precisely milled grooves to gear the ball back to center for accuracy and consistency on impacts across the face. Two front-to-back sight lines frame the ball at address to help golfers sink more putts.Represents a streamlined blend of design and performance technology to inspire greater confidenceSuper stable mallet profile that features a single-bend shaft and face-balanced design for ultra-high MOIDesigned to eliminate mis-hits by broadening the sweet spot to create the sweetest face in golfSweet Face Technology utilizes closely spaced grooves to create superior roll and softer impactLightweight 6062 aluminum body combined with a rear CNC milled 303 Stainless steel “Outback” shaped weightPatented, precise face milling imparts progressively more energy transfer on off-center hitsUnique milling pattern gears ball back to center for accuracy and consistency across faceEach specific putter milled to a specific head weight to maintain swing weight for each lengthTwo front-to-back sight lines frame the ball at address to help golfers accurately line putts upEach head precision milled from 303 SS, then hand ground, finished and assembledBlack armour finish provides a timeless, player-preferred aestheticShaft: FST Stepless, .370” tip diameterER5 Center Shaft Hatchback A center-shafted winged mallet design with a “hatched out” center section. Patented.• CNC Milled in Carlsbad, California USA • Head Material – 303 stainless steel • Color – Silver satin finish • Swing Weight Balanced By Length – 33"@E1, 34”@D9, 35"@E2 • Face Loft – 2 degrees from the shaft • Lie Angle – 70 degrees • Stock Grip – Custom EVNROLL non-taper 1.2 • Length – Measured from center of leading edge to butt • Balance – 10 degrees toe down • Shaft – FST stepless, .370” tip • Shafting – straight shaft mounted over a hosel pinER5 Hatchback – a classic heel-toe weighted flange blade. • CNC Milled in Carlsbad, California USA • Head Material – 303 stainless steel • Color – Silver satin finish • Shaft Lengths & Head Weights– 35’@355g, 34”@370g, 33”@385g • Face Loft – 2 degrees from the shaft • Lie Angle – 71 degrees • Stock Grip – Custom Winn ProX 1.18 • Length – Measured from center of leading edge • Balance – 5 degrees toe down • Shaft – FST stepless, .370” tip • Shafting – Single bend mounted directly into the head ER5 Hatchback Black – a winged mallet design with a “hatched out” center section. • CNC Milled in Carlsbad, California USA • Head Material – 303 stainless steel • Color – Black armour finish • Swing Weight Balanced By Length – 33"@E1, 34"@E1, 35"@E4 • Face Loft – 2 degrees from the shaft • Lie Angle – 70 degrees • Stock Grip – Custom EVNROLL black pistol grip • Length – Measured from center of leading edge to butt • Balance – 25 degrees toe down • Shaft – FST stepless, .370” tip with black armour finish • Shafting – Single bend mounted directly into the head ER6 iRoll-B – an extreme center mass weighted deep mallet. • CNC Milled in Carlsbad, California USA • Head Material – Black anodized 6061 aluminum, 303 stainless steel rear-center weight • Shaft Lengths & Head Weights– 35’@355g, 34”@370g, 33”@385g • Face Loft – 2 degrees from the shaft • Lie Angle – 70 degrees • Stock Grip – Custom EVNROLL non-taper 1.2 • Length – Measured from center of leading edge to butt • Balance – 12 degrees toe down • Shaft – FST stepless, .370” tip • Shafting – Single bend mounted directly into the head ER7 FullMallet – a rear perimeter weighted full mallet. • CNC Milled in Carlsbad, California USA • Head Material – 303 stainless steel • Color – Silver satin finish • Shaft Lengths & Head Weights– 35’@355g, 34”@370g, 33”@385g • Face Loft – 2 degrees from the shaft • Lie Angle – 70 degrees • Stock Grip – Custom EVNROLL non-taper 1.2 • Length – Measured from center of leading edge to butt • Balance – 23 degrees toe down • Shaft – FST stepless, .370” tip • Shafting – Single bend mounted directly into the head ER8 TourMallet – a classic mid-sized players mallet. • CNC Milled in Carlsbad, California USA • Head Material – 303 stainless steel • Color – Silver satin finish • Shaft Lengths & Head Weights– 35’@355g, 34”@370g, 33”@385g • Face Loft – 2 degrees from the shaft • Lie Angle – 70 degrees • Stock Grip – Custom EVNROLL non-taper 1.2 • Length – Measured from center of leading edge to butt • Balance – 23 degrees toe down • Shaft – FST stepless, .370” tip • Shafting – Single bend mounted directly into the head ER8.3 Players Mallet – Flow neck players midmallet. • CNC Milled in Carlsbad, California USA • Head Material – 303 stainless steel • Color – Silver satin finish • Swing Weight Balanced By Length – 33"@E1, 34"@E1, 35"@E4 • Face Loft – 2 degrees from the shaft • Lie Angle – 70 degrees • Stock Grip – Custom EVNROLL red pistol grip • Length – Measured from center of leading edge to butt • Balance – 60 degrees toe down • Shaft – FST stepless, .370” tip • Shafting – Single bend mounted directly into a flow neck heel hosel